Meter and isolation test
The technician shuts off fixtures and watches the meter, then isolates the hot and cold sides of the system. This tells them whether the leak is on a hot or cold line, and whether it is under the house or in the yard.
Pinpoint a hidden leak under your concrete floor before anyone breaks concrete. Local leak detection specialists use pressure tests, acoustic listening, and thermal imaging to find the spot, usually within a few feet.
Call Now · (310) 928-3074
Photo: Timur Shakerzianov on Unsplash
Slab leak detection is the process of confirming that a pressurized water line under your foundation is leaking, then locating the leak precisely enough that a repair can be planned with as little demolition as possible. Good detection is the difference between opening one small section of floor and tearing up an entire room.
In most Rancho Palos Verdes homes the supply lines run through or under the slab, so a leak can drip for months without a visible puddle. The water soaks into the soil below the house, which is why the first clue is usually a higher water bill, a warm patch of floor, or the sound of running water when everything is turned off.
Detection is normally a separate visit from the repair. Once the leak is marked, you can decide on a spot repair or reroute with real information instead of guesswork.
Most technicians combine two or three of these methods to confirm a reading before marking the floor.
The technician shuts off fixtures and watches the meter, then isolates the hot and cold sides of the system. This tells them whether the leak is on a hot or cold line, and whether it is under the house or in the yard.
Each line is pressurized and monitored with a gauge. A steady pressure drop confirms a leak in that line and rules out dripping fixtures or a running toilet.
Ground microphones amplify the hiss of water escaping under pressure. The technician moves across the floor and follows the sound to its loudest point.
Infrared cameras show heat spreading through the slab from a hot-water leak. It is fast and especially useful for warm-floor complaints.
Electronic locators map where pipes actually run under the slab, so the repair team knows the route and depth before cutting.
For quiet or very slow leaks, a safe hydrogen-nitrogen mix is pushed through the line and detected where it rises through the concrete.
| Situation | Methods usually used | Why |
|---|---|---|
| Warm spot on the floor | Thermal imaging + acoustic | Heat signature shows a hot-water leak; sound confirms the exact point |
| High bill, no visible signs | Meter isolation + pressure test | Confirms which line is leaking before searching |
| Running water sound at night | Acoustic listening | Pressurized leaks are loudest when the house is quiet |
| Very slow or intermittent leak | Tracer gas | Finds leaks too small to hear reliably |
| Leak may be in the yard | Line tracing + acoustic | Separates the main service line from under-slab plumbing |
Much of Rancho Palos Verdes was built between the 1950s and the 1970s, when copper supply lines were routinely laid in or under slab-on-grade foundations. After 50 years or more, that copper can develop pinhole leaks from water chemistry and from rubbing against concrete and gravel.
The Peninsula's expansive clay soils swell when wet and shrink when dry, which slowly flexes slabs and the pipes inside them. In the eastern part of the city, ground movement in the Portuguese Bend landslide complex adds more stress. Hillside lots also mean pipe runs can be long and deep, which makes careful line tracing worth the time.
Leak noise also travels differently through a thick slab on clay than through a thin slab on sand. An experienced technician will confirm an acoustic reading with a second method before marking the floor.
Electronic leak detection is usually a flat-rate visit. Most homeowners pay in the low hundreds of dollars, with more for large homes, multiple suspected leaks, or tracer-gas testing. Ask whether the detection fee is credited toward the repair if you hire the same company.
Ranges are general industry figures for planning only, not quotes. Los Angeles County labor rates often sit at the upper end. The written estimate from the provider who inspects your home is the number that counts. See the full slab leak repair cost guide and what insurance covers.
| Job | Typical range |
|---|---|
| Standard electronic detection (single home) | $150 – $500 |
| Large home or multiple suspected leaks | $400 – $800 |
| Tracer gas testing | $500 – $1,000+ |
| After-hours or emergency detection | Add $100 – $300 |
Calls are taken from every part of the city in ZIP codes 90274 and 90275. See the neighborhood pages for local details, or the Rancho Palos Verdes slab leak repair overview.
A skilled technician using two or more methods can usually locate a leak within about one to three feet. That accuracy is what keeps the concrete opening small.
Most visits take one to three hours. Large homes, several leaks, or very quiet leaks can take longer.
Yes. Turn off every fixture and appliance, then watch your water meter for 15 to 30 minutes. If the low-flow indicator or dial moves, water is escaping somewhere and professional detection is the next step.
No. Pressure tests, acoustic listening, thermal imaging, and tracer gas are all non-invasive. The floor is only opened later if you choose a direct-access repair.
Some policies cover the cost of finding the leak and accessing it, but usually not the pipe repair itself. Check your policy and keep the detection report for your claim.
Think water is escaping under your floor? Call now to book leak detection with a local specialist.
Call Now · (310) 928-3074Free referral service. Your call connects you with an independent local provider.