1. Confirm the plan
The technician reviews the detection report, explains the options, and gives you a written estimate covering labor, materials, concrete, and any flooring work.
Fix a confirmed leak under your concrete floor the right way for your home: a targeted spot repair, a reroute around the slab, or a lining. Talk to a local slab leak repair specialist about the options and costs.
Call Now · (310) 928-3074
Slab leak repair stops water escaping from a supply line that runs under or through your concrete foundation. Once leak detection has marked the spot, there are three main ways to fix it: open the slab and repair the pipe directly, abandon the leaking section and reroute a new line through the walls or attic, or line the existing pipe from the inside.
The right choice depends on how old your pipes are, where the leak sits, what flooring is on top, and whether this is the first leak or the third. A single pinhole in otherwise healthy copper is a good candidate for a spot repair. Repeated leaks in 50-year-old copper usually point toward rerouting or repiping.
| Direct spot repair | Reroute | Epoxy pipe lining | |
|---|---|---|---|
| How it works | Cut the slab over the leak, replace the damaged pipe section, patch the concrete | Run new PEX or copper through walls or the attic and cap the old line | Clean the pipe and coat the inside with epoxy |
| Floor disruption | Opening of about 2 x 2 ft over the leak | Little to none; small drywall openings | Minimal; access at the ends of the line |
| Best for | One leak in otherwise sound pipe | Older copper, repeat leaks, leaks under finished floors | Pinholes spread along a line that is hard to reach |
| Typical time | 1 – 2 days, plus floor restoration | 1 – 3 days | 1 – 2 days |
| Long-term outlook | Fixes this leak only; others can follow | Removes the problem line from under the slab | Depends on pipe condition and installer |
A typical direct or reroute repair follows these steps. Your provider will confirm the details for your home.
The technician reviews the detection report, explains the options, and gives you a written estimate covering labor, materials, concrete, and any flooring work.
Water is turned off at the main. Floors and furniture are covered, and dust barriers go up if concrete will be cut.
For a spot repair, a small section of flooring and concrete is removed over the marked leak. For a reroute, small openings are made in walls or ceilings along the new route.
The damaged copper is cut out and replaced, or the new line is run and connected. The old under-slab section is capped if it is being abandoned.
The system is pressurized and checked before anything is closed up, so you know the repair holds.
Concrete is patched and drywall closed. Flooring and drywall finish work may be handled by the same company or a separate contractor, so ask up front.
Many Rancho Palos Verdes homes still have their original copper supply lines from the 1950s to the 1970s. When one pinhole appears in pipe that old, a second and third often follow. That is why many local plumbers recommend rerouting the affected line, or the whole house, after a second slab leak.
The Peninsula's expansive clay and slow ground movement, especially near the Portuguese Bend landslide area, keep flexing slabs. A line rerouted overhead or through walls is no longer exposed to that movement, which is a big reason reroutes are popular here.
Flooring also matters. Many homes here have large-format tile, stone, or wide-plank hardwood that is expensive to match. If the leak sits under a finish you want to keep, a reroute can cost less overall than a spot repair plus new flooring.
Price depends mostly on the repair method, how easy the leak is to reach, and what flooring sits on top. Concrete patching is usually included; replacing tile or hardwood often is not. Get the scope in writing before work begins.
Ranges are general industry figures for planning only, not quotes. Los Angeles County labor rates often sit at the upper end. The written estimate from the provider who inspects your home is the number that counts. See the full slab leak repair cost guide and what insurance covers.
| Job | Typical range |
|---|---|
| Direct spot repair (incl. concrete patch) | $1,500 – $4,000 |
| Single-line reroute | $1,500 – $5,000 |
| Epoxy pipe lining | $2,000 – $6,000+ |
| Whole-house repipe (PEX) | $6,000 – $15,000+ |
| Flooring replacement over the repair | Varies by material |
Calls are taken from every part of the city in ZIP codes 90274 and 90275. See the neighborhood pages for local details, or the Rancho Palos Verdes slab leak repair overview.
If your pipes are relatively young and this is the first leak, a spot repair is often reasonable. If the copper is original to a 1960s or 1970s home, or you have had leaks before, rerouting usually saves money and stress over time.
Most spot repairs and single-line reroutes are finished in one to three days. Flooring restoration can add time, depending on materials.
Usually yes. Water will be off for part of the day, and one area of the house may be closed off for concrete work.
Not for long. Water under a slab can damage flooring, encourage mold, and wash out soil beneath the foundation. Even a slow leak raises your bill every day it runs.
Many policies pay to access the leak and repair resulting water damage, but not to fix the worn-out pipe itself. Coverage varies widely, so check your policy and document everything.
Have a confirmed slab leak? Call now to talk through repair options with a local specialist.
Call Now · (310) 928-3074Free referral service. Your call connects you with an independent local provider.