Quick answer: A warm spot that stays warm, especially with a water heater that seems to run all the time, often points to a leaking hot-water line under the slab. Sunlight, radiant heating, and ducts can also warm a floor, so confirm it with a meter test before calling for detection.

Why a slab leak makes the floor warm

Most Rancho Palos Verdes homes built between the 1950s and the 1970s have copper water lines running in or under the concrete slab. When a hot-water line develops a pinhole, hot water escapes into the gravel and soil under the floor. Concrete holds heat well, so the slab above the leak warms up and stays warm.

Because water keeps leaking out, the water heater keeps refilling and reheating. That is why a warm floor and a water heater that never seems to rest so often go together.

Other things that can warm a floor

Before assuming the worst, rule out the harmless causes:

  • Sunlight through a window or sliding door. Check whether the spot is still warm at night.
  • Radiant floor heating in some remodeled homes.
  • Heating ducts or appliances, such as a refrigerator's exhaust or a duct run under the slab.
  • Hot-water recirculation lines, which can make the floor above them slightly warm even without a leak.

The difference: a leak-related warm spot usually stays warm day and night, may slowly grow, and often comes with a higher water bill.

A 15-minute test you can do yourself

  1. Turn off every faucet, shower, appliance, and the irrigation controller.
  2. Find your water meter (usually near the street) and note the reading and the small leak indicator dial.
  3. Close the cold-water inlet valve on top of your water heater. This isolates the hot side of the house.
  4. Watch the meter for 15 minutes.

If the meter stops once the water heater inlet is closed, the leak is very likely on the hot-water side, which fits a warm-floor slab leak. If it keeps moving, the leak is on the cold side or in the yard line. If it never moved at all, you probably do not have an active leak, and the warm spot has another cause.

Remember to reopen the water heater valve when you finish.

What a leak detection specialist will do

A technician confirms the leak with a pressure test on the hot-water line, then pinpoints it, usually with thermal imaging (which shows the heat spreading through the slab) and acoustic listening (which hears the water escaping). Most leaks are located within a few feet, before any concrete is touched. See how slab leak detection works.

Once it is found, the usual options are a spot repair through the floor or a reroute of the hot-water line through the walls or attic. Rerouting is popular under tile and hardwood, because the floor is never opened.

Should you wait?

A hot-water leak wastes water and energy every hour it runs, and the moisture can damage flooring and encourage mold. It will not fix itself. If the meter test points to the hot side, book detection soon. If water is coming up through the floor, treat it as an emergency: shut off the main water valve and turn off the water heater.

For typical prices, see the slab leak repair cost guide.

People Also Ask

Common questions

Is a warm spot on the floor always a slab leak?

No. Sunlight, radiant heat, ducts, and recirculation lines can warm a floor too. A spot that stays warm day and night, along with a busy water heater or higher bill, is the stronger sign.

Can a cold-water slab leak cause a warm floor?

No. Cold-water leaks do not warm the slab. They tend to show up as damp flooring, a higher bill, or a moving water meter instead.

How long can I live with a hot-water slab leak?

It is best not to wait. Even a small leak wastes water and gas or electricity daily, and moisture under the floor can damage flooring and lead to mold.

Will turning off the water heater stop the leak?

Closing the water heater's cold-water inlet valve stops water flowing into the hot side, which stops a hot-water leak until it can be repaired. You will not have hot water while it is closed.

How is a hot-water slab leak usually fixed?

Either by opening the floor and repairing the pipe, or by rerouting the hot-water line through the walls or attic. Under finished floors, rerouting is often the better value.